Products >Protective Flooring / Coating Systems >Epoxy Flooring >INDUFLOOR-IB-SL1000

INDUFLOOR-IB-SL1000

3-Component, High Performance, Solvent-Free, Self-Leveling, Abrasion & Chemical Resistant Epoxy Floor Topping (500mm to 1.5 mm thickness)

Properties:

INDUFLOOR-IB-SL1000 is 3-component, solvent: tree (100 % solid), self-smoothing & levelling, epoxy resin-based high-build, high performance, chemical & abrasion resistant seamless protective floor coating with dry film thicknesses between 500u and 1.50 mm. After curing the applied material provides a durable, easy-to-clean, protective, sealing & decorative topping with excellent abrasion & impact resistant properties. INDUFLOOR-IB-SL1O00 is based on selected epoxy resins & special hardeners and hard wearing fillers. INDUFLOOR-IB-SL1000 is available in a select of RAL shades.

Areas of Application:

INDUFLOOR-IB-SL1000 provides a seamless, slip, abrasion & chemical resistant floor protective coating that adheres well to both dry and damp concrete, mortar or masonry surfaces. It suitable for areas where a thin to medium film is required such as:

  • Heavy Industries: steel works
  • Schools
  • Soft drink factories
  • Workshops & garages
  • Dairies
  • Kitchens
  • Pharmaceutical plants
  • Showrooms
  • Storage areas
  • Food processing areas
  • Car parks
  • Laboratories
  • Clean rooms
  • Traffic decking
  • Hospitals

Advantages:

  • Easily applied by brush or roller.
  • High build, DFT: 0.5 – 1.5 mm.
  • Smooth surface; easy to clean.
  • Seamless and impermeable.
  • Does not support bacterial growth.
  • Solvent-free (100 % Solid), odour-less.
  • Highly durable; excellent abrasion and impact resistance.
  • Hygienic & impervious to most liquids.
  • Excellent adhesion to sound concrete & masonry substrates.
  • Excellent adhesion to old & new and both dry & damp surfaces.
  • High chemical resistant to most common chemical reagents.
  • Formulated for the Middle East climate.

Technical Data

  • Appearance (mixed): Pigmented free flowing
  • Specific gravity: 1.55 at 20 °C
  • Solid content: 100 % by weight
  • Pot-life: 100-120 mins at 25 °C
  • Full cure: 7 days at 25 °C
  • Bond Strength: > 2.5 N/mm2
  • Wet & dry film thickness: 500 – 1500 microns in a single coat as required
  • Abrasion resistance: 7O mg (Taber Abrasive, 1000 grams / 1000 revolution)
  • Chemical Resistance: INDUFLOOR-IB-SL3000 has been tested for chemical resistance to a comprehensive range of industrial & domestic chemicals. After constant immersion for 9O days at 35 °C in accordance with ASTM D-2240 (Shore D hardness)

Product Details

Product Preparation:

Surface Preparation

All surfaces must be sound, clean and free from dust, grease & oils, curing agents, mould release agents and other contaminations adversely affecting bond with the substrate. Steel or metal surfaces should be free from rust or scale in accordance with SA 2&2 (white metal finish). All adhesion preventing contaminants should be fully removed.

Product Priming:

Priming

Prior to application of INDUFLOORIB-SL1000, use as appropriate INDUFLOOR-IB1 280 or INDUFLOOR-IB1285

Product Mixing:

Mixing

Stir well, each of components A & B (separately) prior to the mixing of the two components. Empty the entire contents of component B into the canister of component A. Using an appropriate drill (RPM approx. 400) attached with an approved mixing paddle, mix the entire contents well for at least 3 minutes until a uniform colour and consistency are achieved. Gradually add – whilst mixing – the entire contents of Component C and continue to mix until a uniform colour and consistent mix is achieved.