Products >Grout, Anchors & Bonding Agents >Epoxy Bonding Agent / Filler >ASO®-Fugenbunt

ASO® Fugenbunt

Standard fine grout

Properties:

For interior use
• Can be washed off early.
• Smooth consistency.
• Vapour permeable.
• Cures free from cracks.
• Good application and
wash-off properties
• Resistant to freeze/thaw cycles.
• For heated floors and walls.
• Free from the silicosis hazard – fine quartz dust.
• Colours matched to the ESCOSIL-2000 range.
• Fulfils the requirements for CG2 to DIN EN 13888.
• For joint widths from 1.5 to 6 mm.

Areas of Application:

ASO-Fugenbunt is especially suitable for grouting absorbent ceramic tiles made from red or white bodied biscuit. The grouting performance, the stiffening in the joint, the water retention and the wash off properties are tailored to suit these tiles. ASO-Fugenbunt is used for joint widths up to 6 mm in interior areas, on walls and floors, in dry, splash contact and wet areas. For grouting floor areas we recommend ASO-Flexfuge, for heavy duty areas HF05-Brillantfuge or ASODUR-DESIGN. For grouting natural stone, fully vitrified and other tiles with low water absorption, glass mosaics and tiles, we recommend CRISTALLFUGE-PLUS.

Storage:

dry, 12 months in the original unopened packaging. Use opened packaging promptly.

Technical Data:

      • Composition:cement, mineral aggregates and high quality additives
      • Colour:White, silver grey Only in 5 kg bags: jasmin, pergamon, bahama beige, beige, caramel, jura beige, grey, titanium grey, medium grey, brown, nut brown, graphite, sand grey
      • Joint widths:1.5 to 6 mm
      • Pot life *: Substrate / approx. 60 mins
      • application temperature: +5° C to +25° C
      • Foot traffic after *:approx. 12 hrs
      • Full service conditions after *:earliest 2 days
      • Water demand:5.0–6.0 litres / 20 kg or
        1.25–1.5 litres / 5 kg
      • Cleaning:whilst still fresh with water
      • Bulk density:approx. 1.26 kg/dm3
      • Fresh mortar density:approx. 1.9 kg/dm3
      • Packaging: 20 kg and 5 kg bags

* Values relate to +23° C room temperature and 50% relative humidity.

Product Details

Product Application:

Only mix ASO-Fugenbunt with clean water in a clean mixing bucket

Only mix ASO-Fugenbunt with clean water in a clean mixing bucket. Place 1.25 to 1.5 l water into the bucket, dependent on the desired consistency, add 5 kg ASO-Fugenbunt and then mix to a homogenous, smooth
mass.
Vitrified tiles:
approx. 1.25–1.35 l water : 5 kg ASO-Fugenbunt
White and red-bodied earthenware tiles:
approx. 1.35–1.5 l water : 5 kg ASO-Fugenbunt.
We recommend mixing with a suitable mixing tool (speed approx.300–500 rpm). After a standing time of 2 mins, remix the grout. In order to avoid colour variations, keep the mixing ratio the same.

Product Work:

Work the ASO-Fugenbunt into the wall

Work the ASO-Fugenbunt into the wall or floor tile joints using a grout float and light pressure. Strike off diagonal to the joints so that the joint section is completely filled. In order to ensure the joints are completely filled in one application, only strike off excess grout cleanly and diagonally to the joints after a short wait (30 – 60 seconds).

Product Stiffened:

Once the grout has stiffened

Once the grout has stiffened (check with a finger test) wash the grout contours with a dampened sponge. After a few minutes wash clean with a sponge board.

Product Brochure:

Brochure

download brochure sheet